Icom IC-FR4000 Repeater

Image
Image
Image

Specification

Icom Specification Page:
http://www.icomamerica.com/en/products/systems/repeaters/fr3000_fr4000/specifications.aspx



[Top][Home]


Manuals

Service Manual:

Icom-RF4000-Service-Manual.pdf

REMOTE CONTROL MANUAL - VHF FM REPEATER IFR3000 and UHF FM REPEATER IFR4000

IC-FR3000_FR4000_Remote_Control.pdf (Local)

FR4000 FR4100 Service Manual - ADDENDUM:
FR4000_FR4100-Service-Manual-ADDENDUM.pdf

Instruction Manual:
FR3000_4000-Instruction-manual.pdf

Version 1.0 November 2007 IC-FR3000/FR4000 Series Sales Handbook:
ICOM-IC-FR3000-FR4000-Sales-Handbook-red-v10.pdf

CW Identification Setup:
ICOM-CW-ID-repeater-setup.pdf

[Top][Home]


Remote Connector

Image

[Top][Home]


Accessory Connector

Image
ImageAugust 31, 1998 Hitachi to Release H8S/2633F and Two Other 16-bit Single-Chip Microcomputer Models with 256-kbyte On-Chip Flash Memory

August 31, 1998 Hitachi to Release H8S/2633F and Two Other 16-bit Single-Chip Microcomputer Models with 256-kbyte On-Chip Flash Memory [Top][Home]


Front Panel - RJ45 Mic-Spk and Programming Jack

RJ45-Mic-Spk-Jack

Front panel pinouts

[Top][Home]

Programming Software

A correctly specified programming cable is required: 3.5mm to USB or RS232 Programming Cable
Programmin Cable OPC-478
Compatible Models are OPC-478 and OPC-478U
[Top][Home]


USB Program Programming Cable

Serial-Programming-Cable Serial-Programming-Cable Serial-Programming-Cable
USB Program Programming Cable For Icom Radio FR4000

[Top][Home]


cpu HD64F2238F

News Release August 31, 1998 - Hitachi to Release H8S/2633F and Two Other 16-bit Single-Chip Microcomputer Models with 256-kbyte On-Chip Flash Memory:
https://www.hitachi.com/New/cnews/E/1998/980831B.html

[Top][Home]

Serial Program Programming Cable

August 31, 1998 Hitachi to Release H8S/2633F and Two Other 16-bit Single-Chip Microcomputer Models with 256-kbyte On-Chip Flash Memory Note:
The Icom OPC-478 cable is a serial cable with a DB9-pin serial connector and uses native RS-232 protocol
The Icom OPC-478UC is virtually the same cable but has a built-in USB to serial chip

Programmin Cable RJ45 Front Programmin Cable RJ45 Rear Programmin Cable Full View
Serial Program Programming Cable For Icom Radio OPC-592IC-FR3000 ICFR3100 FR4000
DB9 - DB25 conversion
DB9	DB25	Function
1	8	Data carrier detect
2	3	Receive data
3	2	Transmit data
4	20	Data terminal ready
5	7	Signal ground
6	6	Data set ready
7	4	Request to send
8	5	Clear to sendAugust 31, 1998
Hitachi to Release H8S/2633F and Two Other 16-bit Single-Chip Microcomputer Models with 256-kbyte On-Chip Flash Memory
9	22	Ring indicator


[Top][Home]


August 31, 1998 Hitachi to Release H8S/2633F and Two Other 16-bit Single-Chip Microcomputer Models with 256-kbyte On-Chip Flash Memory

Programming the FR4000 for AllStar

Configure the IC-FR4000 to use an external controller; so the Icom effectively becomes a full-duplex base station. Then, use AllStar as the external controller. This should work great; AllStar is a very competent repeater controller.

There is a software switch in the programming EPPT that needs to be set to allow pin 19, external PPT, to operate.

In the software for the FR4000 under Expert->>ACC CH Selector to enable. On the front of the repeater press the remote button which enables the External PTT on pin 19August 31, 1998 Hitachi to Release H8S/2633F and Two Other 16-bit Single-Chip Microcomputer Models with 256-kbyte On-Chip Flash Memory

August 31, 1998 Hitachi to Release H8S/2633F and Two Other 16-bit Single-Chip Microcomputer Models with 256-kbyte On-Chip Flash Memory Serial-Programming-Cable
The Remote Button on the IC4000 front panel must be switched ON to allow the enabled External PTT to go to pin 19 of the interconnecting cable that goes to the AllStar node.

[Top][Home]


Multiple AllStar Nodes on the Same LAN

August 31, 1998 Hitachi to Release H8S/2633F and Two Other 16-bit Single-Chip Microcomputer Models with 256-kbyte On-Chip Flash Memory In order Two nodes on the same LAN you need to change the bindport in iax.conf to something other then 4569 on one and manager.conf port to something other then 5039. For example use 4575 and 5040 on one and different for the other two. I have three inside the same LAN with fixed ip on each and each August 31, 1998 Hitachi to Release H8S/2633F and Two Other 16-bit Single-Chip Microcomputer Models with 256-kbyte On-Chip Flash Memorydifferent port numbers and ssh ports as I don’t use the default 222 on any of them. Each should have their own ssh port which would be forwarded in the router.

[Top][Home]


Front Panel Board Repair

Serial-Programming-Cable Serial-Programming-Cable Serial-Programming-Cable Serial-Programming-Cable Serial-Programming-Cable

[Top][Home]

DIY Programming Cable Adaptor

Serial-Programming-Cable

[Top][Home]


A programming Serial Interface Circuit

ICOM-civ-ARRL-Handbook.png

[Top][Home]
Glenn Lyons VK4PK
glenn@LyonsComputer.com.au
Ver:gnl20190307 - pre published v0.9